View A050FW02V0_3488647.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

customer approval sheet company name model a050fw02 v0 customer approved title : name : approval for specifications only (spec. ver. ) approval for specifications and es sample (spec. ver. ) approval for specifications and cs sample (spec. ver. ) customer remark : auo pm : jesse kao p/n : 97.05a10.000 comment : www.datasheet.co.kr datasheet pdf - http://www..net/
all rights strictly reserved. any portion of this pa per shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. doc. version : 0.0 total pages : 28 date : 2009/09/07 product specification 5" color tft-lcd module/panel model name: a050fw02 v0 97.05a10.000 < >preliminary specification < >final specification note: the content of this specification is subject to change. ? 2009 au optronics all rights reserved, do not copy. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 1/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. record of revision version revise date page content 0.0 first draft www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 2/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. contents a. general information................................ ................................................... .................................................. 3 b. outline dimension .................................. ................................................... .................................................. 4 1. tft-lcd module C front and rear view............ ................................................... ..................................... 4 c. electrical specifications .......................... ................................................... ................................................ 5 1. tft lcd panel pin assignment .................... ................................................... .......................................... 5 2. absolute maximum ratings........................ ................................................... .............................................. 7 3. electrical dc characteristics...................... ................................................... .............................................. 7 4. electrical ac characteristics ...................... ................................................... .............................................. 8 5. serial interface characteristics .................. ................................................... ............................................ 10 6. power on/off characteristics..................... ................................................... ............................................ 16 d. optical specification .............................. ................................................... ................................................ 17 e. touch screen panel specifications .................. ................................................... .................................... 19 1. fpc pin assignment .............................. ................................................... ................................................ 19 2. electrical characteristics ......................... ................................................... ............................................... 19 3. mechanical characteristics ........................ ................................................... ............................................ 20 4. life test condition ............................. ................................................... ................................................... .. 20 5. attention....................................... ................................................... ................................................... ........ 21 f. reliability test items ............................. ................................................... ................................................. 22 g. packing and marking ................................ ................................................... .............................................. 24 1. packing form ...................................... ................................................... ................................................... 24 2. module/panel label information .................. ................................................... .......................................... 25 3. carton label information........................ ................................................... ................................................ 25 h. precautions ........................................ ................................................... ................................................... .. 26 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 3/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. a. general information for portable pnd application, this product is an a-s i type thin film transistor liquid crystal display (tft-lcd). this model is composed of a tft-lcd, a dr iver, an fpc (flexible printed circuit), a backlight unit and a touch panel. no. item unit specification remark 1 screen size inch 5.0(diagonal) 2 display resolution dot 480rgb (h) x 272 (v) 3 overall dimension mm 120.7(h) x 75.8(v) x 4.25(t) note 1 4 active area mm 110.88 (h) x 62.832 (v) 5 pixel pitch mm 0.231 (h) x 0.231 (v) 6 color configuration -- r. g. b. stripe note 2 7 color depth -- 262k colors note 3 8 ntsc ratio (cell) % 54 9 display mode -- normally white 10 panel surface treatment -- anti-glare, 3h 11 weight g 80 12 power consumption mw 930 note 4 13 viewing direction 6 oclock (gray inversion) note 1: not include blacklight cable and fpc. refer next page to get further information. note 2: below figure shows dot stripe arrangement. note 3: the full color display depends on 18-bit dat a signal (pin 39~56) . note 4: please refer to electrical characteristics chapter. . . ( 1 2 3 .478 479 480) (1 ..272) www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 4/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transforme d to any other forms without permission from au optronics corp. b. outline dimension 1. tft-lcd module C front and rear view www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 5/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. c. electrical specifications 1. tft lcd panel pin assignment recommended connector : fh26g-67s-0.3shbw(6) no. pin name i/o description remarks 1 vled- p power for led backlight cathode 2 vled+ p power for led backlight anode 3 dgnd p grounding for digital circuit 4 x1 i/o touch panel right electrode 5 y2 i/o touch panel bottom electrode 6 x2 i/o touch panel left electrode 7 y1 i/o touch panel top electrode 8 agnd p grounding for analog circuit 9 vgh c stabilizing capacitor (2.2uf/16v) 10 c5m c booster capacitor(2.2uf/6.3v) 11 c5p c booster capacitor(2.2uf/6.3v) 12 c1ap c booster capacitor(2.2uf/6.3v) 13 c1am c booster capacitor(2.2uf/6.3v) 14 vgl c stabilizing capacitor (2.2uf/16v+schottkydiode: turn on voltage=0.2v) 15 c1bp c booster capacitor(2.2uf/6.3v) 16 c1bm c booster capacitor(2.2uf/6.3v) 17 agnd p grounding for analog circuit 18 vcc25 c stabilizing capacitor (2.2uf/6.3v) 19 c4p c booster capacitor(1uf/16v) 20 c4m c booster capacitor(1uf/16v) 21 avdd p digital and charge pump supply voltage input pin fo r booster circuit (3.3v)+(4.7uf/6.3v) 22 id2 i/o low - low 23 agnd p grounding for analog circuit 24 vcc c stabilizing capacitor (2.2uf/6.3v) 25 c3p c booster capacitor(1uf/16v) 26 c3m c booster capacitor(1uf/16v) 27 id1 i/o connect to pgnd on fpc 28 grb i system reset pin(active low) 29 pgnd p grounding for booster circuit 30 dvdd p digital interface supple voltageinput (1.8v/3.3v)+(2 .2uf/6.3v) 31 cavdd c stabilizing capacitor (4.7uf/10v) 32 pgnd p grounding for booster circuit 33 stb i standby control signal www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 6/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. no. pin name i/o description remarks 34 csb i chip select pin of serial interface 35 sda i data input pin in serial mode 36 scl i clock input in serial mode 37 vint2 c stabilizing capacitor (2.2uf/16v) 38 den i display enable pin from controller 39 b7 i blue data 40 b6 i blue data 41 b5 i blue data 42 b4 i blue data 43 b3 i blue data 44 b2 i blue data 45 g7 i green data 46 g6 i green data 47 g5 i green data 48 g4 i green data 49 g3 i green data 50 g2 i green data 51 r7 i red data 52 r6 i red data 53 r5 i red data 54 r4 i red data 55 r3 i red data 56 r2 i red data 57 nc - no connection 58 nc - no connection 59 clk i dot-clock and oscillator source 60 vint1 c stabilizing capacitor(4.7uf/10v) 61 pgnd p grounding for booster circuit 62 vint3 c stabilizing capacitor(4.7uf/10v) 63 vcomh c stabilizing capacitor(4.7uf/6.3v) 64 vcoml c stabilizing capacitor(4.7uf/6.3v) 65 dgnd p grounding for digital circuit 66 c2p c booster capacitor(1uf/10v) 67 c2m c booster capacitor(1uf/10v) i: input, o: output, p: power www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 7/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. 2. absolute maximum ratings item symbol condition min. max. unit remark analog power voltage avdd gnd=0 -0.3 5 v logic power voltage dvdd gnd=0 -0.5 5 v input signal voltage data gnd=0 -0.3 3.6 v digital signals note 1: functional operation should be restricted un der ambient temperature (25 ). note2: maximum ratings are those values beyond whic h damages to the device may occur. functional operation should be restricted to the limits in the electrical characteristics chapter. 3. electrical dc characteristics a. typical operation condition (gnd = 0v) item symbol min. typ. max. unit remark analog power voltage avdd 3.0 3.3 3.6 v digital interface power voltage dvdd 1.7 - vdd v h level vih 0.7 x dvdd -- dvdd v digital input signal voltage l level vil gnd -- 0.3 x dvdd v b. current consumption (gnd=0v) parameter symbol condition min. typ. max. unit remark i vdd avdd=3.3v - tbd - m a note 1, 2 input current for avdd i vdd (standby) avdd=3.3v - tbd ua note 3 note 1:test condition is under typical eletrical dc and ac characteristics. note 2: test pattern is the following picture. note 3:in standby mode, all digital signals are sto pped. ex. dclk,de ..etc. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 8/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. c. backlight driving conditions the backlight (led module, note 1) is suggested to dr ive by constant current with typical value. parameter symbol min. typ. max. unit remark led current i l -- 20 22 ma note 1 power consumption v l -- 924 1108.8 mw led life time l l 10,000 -- -- hr note 2, 3 note 1:led backlight is two parallel strings and one led for each string is as below figure. suggest to drive by 20ma for each led string. note 2:define led lifetime: brightness is decreas ed to 50% of the initial value. led lifetime is restricted under normal condition, ambient temperatur e = 25 and led lightbar current = 20ma. note 3:if it uses larger led lightbar voltage/ curre nt more than 20ma, it maybe decreases the led lifetime. 4. electrical ac characteristics a. signal ac characteristics parameter symbol min. typ. max. unit remark dclk clock time t clk 83 - - ns parallel rgb mode clock rising time t rck 9 - - ns clock falling time t fck 9 - - ns hsd width t hwh 1 - - dclk hsd period time t h 55 - - us hsd setup time t hsu 12 - - ns hsd hold time t hhd 12 - - ns vsd width t vwh 1 - - th vsd setup time t vsu 12 - - ns vsd hold time t vhd 12 - - ns de setup time t desu 12 - - ns de hold time t dehd 12 - - ns data setup time t dst 12 - - ns data hold time t dhd 12 - - ns www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 9/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. b. input timing vertical timing of input horizontal timing of input parallel rgb mode data format www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 10/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. parallel rgb input timing table 5. serial interface characteristics 5.1 3-wire command format the 3-wire communication can be bi-directionally contro lled by the r/w bit in the address field. the 3-wire engine acts as a slave mode at all times, and will not issue any command to the 3-wire bus itself. under read mode, the 3-wire engine will return the data during data phase. the returned data should be latched at the rising edge of scl by an external controller. data in the hi-z phase will be ignore d by the 3-wire engine during write operation, and sh ould be ignored during read operation as well. during read operation, an external controller should float the sda pin under hi-z phase and data phase. each read/write operation should be exactly 16 bits. to prevent incorrect setting of the internal register , any write operation with more or less than 16 bits of data during a csb low period will be ignored by the 3-wire engine. to prevent incorrect setting of the internal register , refer to the section 3-wire timing diagram for detailed timing. parameter symbol min typ max unit dclk frequency fclk 5 9 12 mhz horizontal signal hsd period time th 520 525 800 dclk hsd display area thd - 480 - dclk hsd back porch thbp 36 40 255 dclk hsd front porch thfp 4 5 65 dclk vertical signal vsd period time tv 277 288 400 h vsd display area tvd - 272 - h vsd back porch tvbp 3 8 31 h vsd front porch tvfp 2 8 93 h www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 11/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. 3-wire command format: bit description d15-d10 register address [5:0]. d9 w/r control bit. 0 for write; 1 for read d8 hi-z bit during read mode. any data within this bits will be ig nored during write mode d7-d0 data for the w/r operation to the address indicated by address pha se 3-wire writer format: msb lsb d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 register address [5:0] 0 x data (issue by external controller) 3-wire read format: msb lsb d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 register address [5:0] 1 hi-z data (issue by 3-wire engine) 5.2 3-wire control register list address r/w msb initial value lsb no. d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 hsdpol vsdpol clkpol fpol nfsel 00 dithb r0 0 0 0 0 0 0 r/w(0) x 0 0 0 0 0 0 0 0 0 0 1 stb grb shlr updn r1 0 0 0 0 0 1 r/w(0) x 0 0 0 1 1 1 1 1 ddl[7:0] r4 0 0 0 1 0 0 r/w(0) x 0 0 1 0 1 0 0 0 hdl[4:0] r5 0 0 0 1 0 1 r/w(0) x 0 0 0 0 1 0 0 0 0 vcomh[6:0] r6 0 0 0 1 1 0 r/w(0) x 0 1 0 0 1 1 0 1 0 vcoml[6:0] r7 0 0 0 1 1 1 r/w(0) x 0 0 0 1 1 0 1 1 bri[7:0] r8 0 0 1 0 0 0 r/w(0) x 0 1 0 0 0 0 0 0 con_b[7:0] r9 0 0 1 0 0 1 r/w(0) x 0 1 0 0 0 0 0 0 sub_bri_r[6:0] r10 0 0 1 0 1 0 r/w(0) x 0 1 0 0 0 0 0 0 sub_con_r[6:0] r11 0 0 1 0 1 1 r/w(0) x 0 1 0 0 0 0 0 0 sub_bri_b[6:0] r12 0 0 1 1 0 0 r/w(0) x 0 1 0 0 0 0 0 0 sub_con_b[6:0] r13 0 0 1 1 0 1 r/w(0) x 0 1 0 0 0 0 0 0 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 12/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. 5.3 suggested serial command settings 5.4 3-wire registers function description r0: timing controller function register designation address description dithb r0[0] dithering control bit. dithb=1, dithering off, (7-bits resolution, truncat ion last 1-bits of the input data) dithb=0, dithering on, (pseudo 8-bits resolu tion). (default) nfsel r0[3] narrow display mode selection bit. nfsel=1: narrow display format is enable. nfsel=0: normally display. (default) fpol r0[4] vcom polarity inverse control bit. when fpol=1, vcom inverse polarity. when fpol=0, vcom normal polarity. (default) clkpol r0[5] dclk polarity control bit. clkpol=1: data sampling at dclk falling edge. clkpol=0: data sampling at dclk rising edge. (def ault) vsdpol r0[6] vsd polarity control bit. vsdpol=1: vsd positive polarity. vsdpol=0: vsd negative polarity. (default) hsdpol r0[7] hsd polarity control bit. vsdpol=1: hsd positive polarity. vsdpol=0: hsd negative polarity. (default) narrow display mode power on den / vsync / hsync / dclk / data input > 100 us register : vdd, vddio input data 0 020h r0 dclk polarity control. 1440 dots 1080 dots 180 dots 180 dots www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 13/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. r1: timing controller function register designation address description updn r1[0] gate driver up/down scan control of gate driver. updn=1, shift from up to down, first line=l1->l2- > ->l543->l544=last line (default) updn=0, shift from down to up, first line=l544->l 543-> ->l2->l1=last line shlr r1[1] right/left sequence control of source driver. shlr=1, shift right: first data=s1->s2->s3 ->s72 0=last data (default) shlr=0, shift left: last data=s1<-s2<-s3 <-s720 =first data grb r1[2] global reset bit. grb=1, normal operation. (default) grb=0, the controller is in reset state. stb r1[3] standby mode selection bit. stb=1, normal operation. (default) stb=0, timing control, driver and dc-dc converter, are off, and all outputs are high-z. note: when shlr=0, input rgb sequence does not need to sweep in serial mode. r1 g1 r2 b1 g2 b2 r479 g479 r480 b479 g480 b480 b1 g1 b2 r1 g2 r2 b479 g479 b480 r479 g480 r480 shlr= 1" shlr= 0" r4: data delay setting designation address description select the hsd signal to 1st input data delay timin g. ddl[7:0] ddl function unit 24h 36(minimum setting for parallel mode) 28h 40(default setting for parallel mode) 6ch 108(minimum setting for serial mode) 78h 120(default setting for serial mode) ddl[7:0] r4[7:0] ffh 255 dclk note: ddl function will be disabled under 8/24 bit de mode. r5: hsd delay setting designatio n addres s description select the gate start pulse output delay timing. hdl[4:0] hdl function unit 02h 2(minimum setting) 08h 8(default) hdl[4:0] r5[4:0] 1fh 31 hsd note: hdl function will be disabled under 8/24 bit de mode. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 14/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. r6: vcomh level control register designation address description vcomh level adjustment. (20mv/lsb) vcomh[6:0] vcomh level unit 00h 2.46 1bh 3 4dh 4 vcomh[6:0] r6[6:0] 7fh 5 v otp_vcom h r6[7] vcomh data source selection register otp_vcomh=1, vcomh is switched to the 3-wire regi ster memory when the user wants to adjust the vcomh level. otp_vcomh=0, vcomh is read from otp memory. (defa ult) note: vcomh setting have to greater then avdd. r7: vcoml control register designation address description vcoml level adjustment. (20mv/lsb) vcoml[6:0] vcoml level unit 00h -0.46 1bh -1(default) 4dh -2 vcoml[6:0] r7[6:0] 7fh -3 v otp_vcom l r7[7] vcoml data source selection register otp_vcoml=1, vcoml is switched to the 3-wire regi ster memory when the user wants to adjust the vcoml level. otp_vcoml=0, vcoml is read from otp memory. (defa ult) r8: brightness control register designation address description brightness level setting; gain changes 1 step/bit bri[7:0] brightness gain 00h dark (-64) 40h center (0) (default) bri[7:0] r8[7:0] ffh bright (+191) www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 15/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. r9: contrast control register designation address description contrast level setting; gain changes (1/64)/bit con[7:0] contrast gain 00h 0 40h 1(default) con[7:0] r9[7:0] ffh 3.984 r10: sub_brightness_r control register designation address description red sub-pixel brightness level setting; setting accu racy: 1 step/bit sub_bri_r[7:0] r brightness gain 00h dark (-64) 40h center (0) (default) sub_bri_r [6:0] r10[6:0] 7fh bright (+63) r11: sub_contrast_r control register designation address description red sub-pixel contrast level setting; gain changes ( 1/256)/bit sub_con_r[7:0] r contrast gain 00h 0.75 40h 1(default) sub_con_ r[6:0] r11[6:0] 7fh 1.246 r12: sub_brightness_b control register designation address description blue sub-pixel brightness level setting; setting acc uracy: 1 step/bit sub_bri_b[7:0] b brightness gain 00h dark (-64) 40h center (0) (default) sub_bri_b [6:0] r12[6:0] 7fh bright (+63) r13: sub_contrast_b control register designation address description blue sub-pixel contrast level setting; gain changes (1/256)/bit sub_con_b[7:0] b contrast gain 00h 0.75 40h 1(default) sub_con_ b[6:0] r13[6:0] 7fh 1.246 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 16/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. 6. power on/off characteristics a. recommended power on sequence the lcd apopts high voltage driver ic, so it could be permanently damaged under a wrong power on/off sequence. the suggested lcd power sequence is below b. recommended power off sequence notes: ic internal default setting stb=1, normal operation. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 17/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. d. optical specification all optical specification is measured under typical co ndition (note 1, 2) item symbol condition min. typ. max. unit remark response time rise tr tf =0 - - 7 23 - - ms ms note 3 contrast ratio cr at optimized viewing 400 500 - note 4 viewing angle top bottom left right cr R 10 - - - - 40 60 70 70 - - - deg. note 5 brightness y l =0 350 400 - cd/m 2 note 6 uniformity 75 - - % note 7 rx =0 0.521 0.571 0.621 ry =0 0.279 0.329 0.379 gx =0 0.289 0.339 0.389 gy =0 0.535 0.585 0.635 bx =0 0.095 0.145 0.195 by =0 0.017 0.067 0.117 wx =0 0.26 0.31 0.36 chromaticity wy =0 0.28 0.33 0.38 note 1: ambient temperature =25 , and led lightbar voltage v l = 12 v. to be measured in the dark room. note 2: to be measured on the center area of panel w ith a viewing cone of 1 by topcon luminance meter bm-5a, after 15 minutes operation. center of the screen field=1 bm-5a www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 18/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. note 3: definition of response time: the output signals of photo detector are measured w hen the input signals are changed from black to white(falling time) and from white to black(rising time), respectively. the response time is defined as the time interval between the 10% and 90% of amplitudes. refer to figure as below. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% note 4.definition of contrast ratio: contrast ratio is calculated with the following for mula. status black" " at is lcd when output detector photo status white" " at is lcd when output detector photo (cr) ratio contrast = note 5. definition of viewing angle, , refer to figure as below. note 6.measured at the center area of the panel whe n all the input terminals of lcd panel are electrically opened. note 7: luminance uniformity of these 9 points is d efined as below: 9) - (1 points 9 in luminance maximum 9) - (1 points 9 in luminance minimum uniformity = www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 19/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. e. touch screen panel specifications 1. fpc pin assignment pin no. symbol i/o description 1 x1 i/o touch panel right electrode (r) 2 y2 i/o touch panel bottom electrode (b) 3 x2 i/o touch panel left electrode (l) 4 y1 i/o touch panel top electrode (u) 2. electrical characteristics item min. typ max. unit remark rate dc voltage - - 7 v x (film) 300 - 1600 resistance y (glass) 100 - 800 at connector linearity -1.5% - 1.5% -- note 1 response time - - 30 ms insulation resistance 20 - - m dc 25v note 1: measurement condition of linearity: differe nce between actual voltage & theoretical voltage is an error at any points. linearity is the value max. error voltage divided by voltage difference on active area. linearity www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 20/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. 3. mechanical characteristics item min. max. unit remark hardness of surface 3 - h jis k-5600 operation force (pen or finger) - 60 gf note 1, 2 chattering - 10 ms note 1: within active area inside 5mm, but not nea r the active area boundary and on the dot-spacer. note 2: operation force measurement is under test c ondition as figure below. 4. life test condition item min. max. unit remark notes life 10 5 -- lines note 1, 2 input life 10 6 -- times note 1, 3 note 1: notes life test condition (by pen): slide on central 2/3 of active area and use r 0.8mm polyacecal pen, input force : 250gf, frequency : 60mm/sec. sliding from a to b com plete 1 time. shown as figure. note 2: input life test condition (by finger): test position on active area center and use r8.0mm silic on rubber (hardness 60 ), test force: 250gf, frequency : 2times/sec. shown as figure. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 21/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. 5. attention please pay attention for below matters at mounting design of touch panel of lcd module. 1) do not design casing opening area pressing the a ctive area to prevent from miss input. suggest casing opening area shown as mechanical drawing. sugg est the gap between caseing and touch panel surface at least 0.5mm to avoid miss input. 2) cushion area must not contact with active area. s uggest cushion area shown as mechanical drawing. 3) use elastic or non-conductive material to enclosur e touch panel. 4) do not bond film of touch panel with casing. 5) the touch panel edge is conductive. do not touch it with any conductive part after mounting. 6) if user wants to cleaning touch panel by air gun , pressure 2kg/cm 2 below is suggested. not to blow glass from fpc site to prevent fpc peeled off. 7) do not put a heavy shock or stress on touch panel and film surface. ex. dont lift the panel by film face with vacuum. 8) do not lift lcd module by fpc. 9) please use dry cloth or soft cloth with neutral detergent (after wring dry) or one with ethanol at cleaning. do not use any organic solvent, acid or alka li liquor. 10) do not pile touch panel. do not put heavy good s on touch panel. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 22/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. f. reliability test items no. test items conditions remark 1 high temperature storage ta= 80 c 240hrs 2 low temperature storage ta= -30 c 240hrs 3 high ttemperature operation tp= 70 c 240hrs 4 low temperature operation ta= -20 c 240hrs 5 high temperature & high humidity tp= 60 c, 90% rh 240hrs operation 6 heat shock -30 ~ 80 , 30 cycles 7 electrostatic discharge contact = 4 kv, class b air = 8 kv, class b note 4 8 image sticking 25 , 5hrs note 5 frequency range : 8~33.3hz stoke : 1.3mm sweep : 2.9g ,33.3~400hz 2 hours for each direction of x,y,z 10 vibration 4 hours for y direction non-operation jis c7021, a-10 condition a : 15 minutes 11 mechanical shock 100g . 6ms, x,y,z 3 times for each direction non-operation jis c7021, a-7 condition c 12 vibration (with carton) random vibration: 0.015g 2 /hz from 5~200hz C6db/octave from 200~500hz iec 68-34 13 drop (with carton) height: 60cm 1 corner, 3 edges, 6 surfaces note 1: ta: ambient temperature. tp: panel surface temperature note 2: in the standard conditions, there is not dis play function ng issue occurred. all the cosmetic specification is judged before the reliability stres s. note 3: all the cosmetic specification is judged befor e the reliability stress. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 23/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. note 4 : all test techniques follow iec6100-4-2 stan dard. test condition note pattern procedure and set-up contact discharge 330?, 150pf, 1sec, 8 point, 25times/point air discharge 330?, 150pf, 1sec, 8 point, 25times/point criteria b C some performance degradation allowed. no data lo st. self-recoverable hardware failure. others 1. gun to panel distance 2. no spi command, keep default register settings. note 5: operate with chess board pattern as figure and lasting time and temperature as the conditions. then judge with 50% gray level, the mura is less th an jnd 2.8 www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 24/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. g. packing and marking 1. packing form www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 25/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. 2. module/panel label information the module/panel (collectively called as the product ) will be attached with a label of shipping number which represents the identification of the product a t a specific location. refer to the product outline drawing for detailed location and size of the label. the label is composed of a 22-digit serial number w ith the following definition: example: 501m06zl06123456781z05: product manufacturing week code: wk50 product version: version 1 product manufactuing factory: m06 3. carton label information the packing carton will be attached with a carton lab el where packing qty, auo model name, auo part number, customer part number (optional) and a serie s of carton number in 13 or 14 digits are printed. the carton number is apparing in the following form at: refer to the drawing of packing format for the locat ion and size of the carton label. www.datasheet.co.kr datasheet pdf - http://www..net/
version: 0.0 page: 26/28 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission from au optronics corp. h. precautions 1. do not twist or bend the module and prevent the unsuitable external force for display module during assembly. 2. adopt measures for good heat radiation. be sure to use the module with in the specified temperature . 3. avoid dust or oil mist during assembly. 4. follow the correct power sequence while operating . do not apply the invalid signal, otherwise, it wi ll cause improper shut down and damage the module. 5. less emi: it will be more safety and less noise. 6. please operate module in suitable temperature. t he response time & brightness will drift by differe nt temperature. 7. avoid to display the fixed pattern (exclude the white pattern) in a long period, otherwise, it will cause image sticking. 8. be sure to turn off the power when connecting or d isconnecting the circuit. 9. polarizer scratches easily, please handle it caref ully. 10. display surface never likes dirt or stains. 11. a dewdrop may lead to destruction. please wipe o ff any moisture before using module. 12. sudden temperature changes cause condensation, an d it will cause polarizer damaged. 13. high temperature and humidity may degrade perfo rmance. please do not expose the module to the direct sunlight and so on. 14. acetic acid or chlorine compounds are not friends with tft display module. 15. static electricity will damage the module, please do not touch the module without any grounded device. 16. do not disassemble and reassemble the module by self. 17. be careful do not touch the rear side directly. 18. no strong vibration or shock. it will cause module broken. 19. storage the modules in suitable environment wit h regular packing. 20. be careful of injury from a broken display module. 21. please avoid the pressure adding to the surface (front or rear side) of modules, because it will cau se the display non-uniformity or other function issue. www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of A050FW02V0

	To Download A050FW02V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .